ND-751T-E Intelligent Plug-in Thermal Detector is a new developed product by NOTIFIER® in order to meet the sophisticated market demands. This new thermal detector has embedded a Central Processing Unit (CPU), and is addressable and software addressing designed; with integral communication provide features that surpass conventional detectors. ND-751T-E detector is compatible with the NOTIFIER® N-6000 Fire Alarm Control Panel (FACP), and is used with B601 Intelligent Detector Base for connection. ND-751T-E detector is designed to provide open area protection, which applicable for areas such as residential buildings, office complexes, schools, college campuses and any others utilities.

The MMX-7-E Intelligent Monitor Module is designed to interface with contact devices, such as security contacts, waterflow switches, conventional manual fire alarm pull-stations, or other normally-open dry-contact alarm activation devices. The MMX-7-E Monitor Module supervises these devices and reports their current statuses and alarm statuses to the control panel. The history of each event is recorded. MMX-7-E Monitor Module is addressable and software addressing designed, each module can be programmed from address 101 to 199 with the address encoder. MMX-7-E Monitor Module is compatible with the NOTIFIER® N-6000 Fire Alarm Control Panel (FACP), and each monitor module occupies one address point in FACP.

The CMX-7C-E is a compact addressable module which contains one control output, provides a circuit for Notification Appliances such as horns, strobes, speakers etc. Addressability allows the CMX-7C-E to be activated, either manually or through panel programming, on a select (zone or area of coverage) basis.

The CMX-7-E Monitor Module is a compact addressable module which contains one relay output and one monitor input. These two input and output points can work independently. The relay output is to activate devices, while the monitor input is to supervise status feedback from the contact devices.

The MMX-7P-E Intelligent Interface Monitor Module allows intelligent panel to interface and monitor two-wire conventional detectors. It transmits the status (normal, open or alarm) of one full zone of conventional detectors back to the control panel. The history of each event is recorded. All two-wire detectors being monitored must be compatible with the module. MMX-7P-E Interface Module is addressable and software addressing designed, each module can be programmed from address 101 to 199 with the address encoder. MMX-7P-E Interface Module is compatible with the NOTIFIER® N-6000 Fire Alarm Control Panel (FACP), and each interface module occupies one address point in FACP. A build-in address bit (not settable) is used by the system to differentiate module address from sensor address.

The NOTIFIER® ISO-7-E Fault Isolator Module is used with the N-6000 Fire Alarm Control Panel (FACP) to protect the system against wire-to-wire short circuits on the SLC loops. The ISO-7-E should be spaced between groups of sensors in a loop to protect the rest of the loop. Use to isolate short circuit problems within a section of a loop so that other sections can continue to operate normally.
If a wire-to-wire short occurs, the ISO-7-E will automatically open-circuit (disconnect) the SLC loop. After the short circuit condition is corrected, the ISO-7-E will automatically reconnect the isolated section of the SLC loop. The ISO-7-E will not require any address setting, and its operations totally automatic. The ISO-7-E can mount in a standard 4.0” (10.16cm) deep electrical box, in a surface-mounted backbox, or in the FACP.

The M700K-E is designed to be as a component of a fire control system using Notifier Company compatible control panel. It is a dedicating addressable call-point for installation on the two-wire communication circuit providing both signaling of alarm to the monitoring control panel and local led indication of activation.

P700A-E is an addressable horn/strobe designed by Notifier. It can communicate with FACP to tiger the alarm or reset. P700A-E supports permanently supervise 24VDC power supply and report to FACP. Device address range: 101-199, and set by handheld encoder.